Dee-zee DZ1933U User Manual download pdf

INSTALLATION INSTRUCTIONS

CONGRATULATIONS

you have purchased the finest quality universal trim products on the market! By following these instructions, you will ensure a

long-lasting quality installation of your U-Cut trim product! Thank you for your purchase!

IMPORTANT NOTICE:

It is extremely important that you follow all instructions properly and thoroughly in order to achieve a

trouble free long-lasting installation! Failure to read and follow these instructions properly could result in an improper

installation and could lead to adhesive failure. Our warranty does not cover product failure due to improper installation! If you

have any questions please go to WWW.U-CUT.NET before beginning the installation.

VEHICLE SURFACE PREPARATION

- Thoroughly wash the area where the U-Cut Kit will be installed. After washing, use Prepsol,

Xylene, Acetone, Methyl Ethyl Ketone (MEK) or similar de-greasing/de-waxing solution to remove any and all waxes, sealants, oils, tar,

and anything else that might interfere with proper adhesion.

Please follow the Manufacturer's use instructions for these products!

DO NOT USE THEM NEAR FIRE OR FLAME

! After completing this step, use Rubbing Alcohol to remove any residue left by the de-

greasing/de-waxing solution. Standard household rubbing alcohol will work great. There must now be a distinct difference between the

prepared surface and the rest of the vehicle! If not, repeat the steps over again until there is a distinct difference! Also, the temperature

of the vehicle surface should be 65 degrees or above to assure good adhesion.

A REMINDER: Taking the extra time to complete

this step properly will minimize the probability of poor adhesion and assure a quality installation!

1. Tools needed: cleaning solution, alcohol, sharp scissors, straight edge, medium point black marker, tape measure

and masking tape.

2. For Rocker Panel Kits, a pattern may be made to fit from body side molding down, from door bottom up, or from

molding to door bottom. The width of material you purchase will dictate how your product will fit. Make sure you

decide where you want to attach your kit before you start tracing and cutting pieces. It's best to do one side of the

vehicle first then do the other side last.

3. Once you decide where you want your pattern to fit, tape a piece of the clear pattern material to the driver side front

door with masking tape. You want to make the largest pieces first and finish with smaller pieces. Use this material

sparingly! DO NOT MAKE A PATTERN PIECE FOR BOTH SIDES OF THE VEHICLE. Most vehicles are the same on

both sides. You should be able to use the same pattern piece on the other side of the vehicle by reversing it. Hold it

up to the same part (door, etc.) on the other side of the vehicle, to be absolutely sure, prior to cutting another pattern!

4. Using your marker, trace the outline of your part on the pattern material, labeling each part as you go. (ie: T for Top

and DR for Driver Side). Usually it is only necessary to mark the front and rear of the pattern so you can cut the

Chrome ABS to length. Make sure to leave a 1/8" reveal of paint on each end of your part. (If you are installing Pillar

Post trim or gas door cover, trace your pattern using a straight edge or protractor for a clean even line.)

5. Once all your pieces are marked, cut out your patterns. Double check the cuts and the fit to make sure they are

exactly what you want. Once you're sure, it’s time to cut the actual Chrome ABS piece.

6. Align your pattern with the Chrome side of the U-Cut material. Maximize the use of your Chrome ABS material by

starting as close to the edge as possible.

7. It's time to cut the Chrome ABS. Use a sharp pair of scissors and take your time. Never fully close your scissor

blades thru the cut for a nicer cut line. Use the sand paper in the kit to 'clean up' any edges or corners by lightly

sanding them. Only sand as necessary.

8. After cutting all of your Chrome pieces, dry fit them again to ensure they are cut correctly.

9. To install, peel the 3M backing from the piece, line it up to the exact position where you made the tracing. Lightly

stick the piece to the vehicle and smooth it from the top down and then from the center to the outside edges. If you

make a mistake, the adhesive is forgiving enough that you can gently remove the part and place it again. Only do this

if absolutely necessary! Repeat this process on each piece. Take your time, your almost there!

10. After the pieces are installed, remove the protective film. Now that one side is done repeat steps 2-10 on the other

side.

Congratulations on designing, producing and installing your own U-Cut trim kit. For further instructions, go to www.u-cut.net.

You will find step by step instructions with pictures or an installation video if you prefer.

NOTICE: DO NOT WASH YOUR VEHICLE FOR AT LEAST 48 HOURS AFTER INSTALLATION!

For warranty information, please see WWW.U-CUT.NET and click on warranties.

INSTALLATION INSTRUCTIONS 1

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CONGRATULATIONS you have purchased the finest quality universal trim products on the market! By following these instruction

Comments to this Manuals

No comments

Dee-zee DZ1933U User Manual

Browse online or download User Manual for For the car Dee-zee DZ1933U. Dee Zee DZ1933U User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Dee-zee DZ1933U