Dee-zee DZ500797 User Manual download pdf (Page 2)

3” BULL BAR

01-06, 07 "CLASSIC" 1500HD CHEVY SILVERADO/GMC SIERRA

99-06, 07 "CLASSIC" 2500LD CHEVY SILVERADO/GMC SIERRA

00-06 2500SUBURBAN

00-06 2500 TAHOE/YUKON, YUKON XL

Page 1 of 3 11/28/11 REV1(DP)

PARTS LIST:

Bull Bar

10mm Lock Washers

Driver/Left Side Mounting Bracket

10-1.5mm Nuts

Passenger/Right Side Mounting Bracket

12-1.75mm x 40mm Hex Bolts

Spacer Plates

12mm x 44mm OD x 4mm Flat Washers

10-1.5mm x 35mm Hex Bolts

12mm Lock Washers

10mm x 30mm OD x 2.5mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. PLASTIC BUMPER COVER M A Y REQUIRE

CUTTING FOR INSTALLATION.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not

required, but strongly recommended. If local/state law requires a license plate, license plate relocation

kit is available.

3. Starting at the passenger/right side, remove the two factory bolts and the tow hook if equipped. NOTE:

This Bull Bar is not compatible with factory tow hooks and they cannot be reinstalled.

a. NOTE: Vehicles without tow hooks. Temporarily remove the lower bumper cover and place it

on a clean, stable work surface, (Figure 1).

4. Select the passenger/right side Frame Bracket. Slide the Frame Bracket into the open end of the frame

channel accessible through the opening in the bumper cover for the tow hook, if equipped, (Figure 2).

5. Line up the (2) welded nuts on the Frame Bracket with the (2) factory holes in the bottom of the frame

channel. Insert (1) 12mm x 40mm Hex Bolt, (1) Spacer Plate, (1) 12mm Flat Washer and (1) 12mm

Lock Washer through the large hole in the bottom of the frame channel and into the threaded nut on the

Frame Bracket. Insert (1) 12mm x 40mm Hex Bolt, (1) 12mm Flat Washer and (1) 12mm Lock Washer

into the remaining factory hole in the frame channel. I M P O R T AN T : Use the (2) Spacer Plates to cover

the large holes in the bottom of the frame channel, (Figure 2). Do not tighten hardware at this time.

6. Repeat Steps 3 - 5 for driver/left side Frame Bracket installation.

7. W it h assistance, position the Bull Bar up to the inside of the Frame Brackets. Bolt the Bull Bar to the

Frame Brackets using the included (4) 10mm x 35mm Hex Bolts, (4) 10mm Lock Washers, (8) 10mm

Flat Washers and (4) 10mm Hex Nuts, (Figure 2). NOTE: Each mounting tab on the Bull Bar has (3)

slots. Determine the correct mounting position for the Bull Bar.

a. 99-02 Vehicles: Push the Bull Bar in toward the vehicle and bolt the Bull Bar to the Brackets

using the forward and center slots only. Do not tighten hardware at this time.

b. 03-06, 07 "Classic" Model Vehicles: Pull the Bull Bar away from the vehicle and bolt the Bull

Bar to the Brackets using the center and rear slots only. Do not tighten hardware at this time.

8. Level, center and adjust the Bull Bar.

a. Vehicles equipped with tow hooks: Tighten all hardware at this time.

b. Vehicles without tow hooks: Tighten the 12mm hardware bolting the Brackets to the frame

channel only. Temporarily remove the Bull Bar. Hold the lower bumper cover up to the (2)

Frame Brackets. Mark the location of the Brackets onto the back of the plastic bumper cover.

Carefully cut out the indented fill panel in the plastic bumper to clear the (2) Brackets, (Figure

1). For a clean installation, remove as little material as necessary to clear the Brackets. Once

properly cut, reinstall the plastic cover with the factory hardware. Reinstall the Bull Bar and

tighten all hardware, (Figure 2).

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

1 2 3 4

Comments to this Manuals

No comments

Dee-zee DZ500797 User Manual Page 2

Comments to this Manuals

Related products and manuals for For the car Dee-zee DZ500797